PS3 Blu Ray Drive

How to Replace a PS3 Blu-ray Drive

PS3 Blu Ray Drive - If your PlayStation 3 (PS3) is no longer recognizable games or Blu-ray, the internal dysfunction of the console, Blu-ray or dead. If the PS3 is under warranty, you can send the console back to Sony for repair. If not under warranty, the cost of repair will be expensive. This will save a considerable amount of money by replacing the Blu-ray disc. Used and reconditioned spare disks can be found online or in stores that sell for a fraction of the cost of sending the Sony console.
  1. Unplug the power cord and all cables from the PS3 PlayStation 3 Set on a table with the front facing up. Use a screwdriver to remove the rubber screw cover on the left side of the PS3.
  2. Use the Torx T10, remove the screw under the rubber cover.
  3. Slide the PS3 as the console on the left side. After removing the clips, lift the plate and remove.
  4. Remove the seven screws that secure the cover. Tape the screws on the top cover near their positions, so you can easily replace the PS3 assembly.
  5. Raise the rear part of the top cover. Outside the PS3 base. Gently shake the top cover toward you until it is completely devoid of basis. Put the cover aside.
  6. Remove the Blu-ray, the power cord from the socket on the motherboard.
  7. Take up the Blu-ray player, not screwed Locate the ribbon cable to the bottom of the disc. Disconnect the ribbon cable from the motherboard by blocking the plug and unplug the power cord from the wall outlet. Remove the old Blu-ray.
  8. Reconnect the ribbon cable to the spare drive to the motherboard. Enter the new internal hard drive. Assemble Connect the power cable to the motherboard and again, the PS3.

How to Clean the Blu-Ray Drive on a PS3


The Sony PlayStation 3 (PS3) is an advanced game console with a Blu-Ray. The Blu-ray is only for the PS3 to play Blu-ray with very high levels compared to standard definition DVDs. Unfortunately, the Blu-Ray to collect dust and can be cleaned to the highest quality work possible. Once you know the correct procedure and have disassembled the PS3, the cleaning can be done.

Disassembling the PS3

  1. Remove the screws that are under the rubber feet on the left side than on the PS3, and security Torx screw that rests on the top cover. Perform this procedure in an environment free of static electricity and remove the PS3 from the power source.
  2. Push the black plastic cover on the left of the PS3, then remove it. There are seven more screws that are currently removed.
  3. Remove the lid and allow the two small tabs using a small screwdriver, gently, without breaking them.
  4. Remove the large silver box, which is Blu-ray, about 2 inches to reveal a large banda. Pulling the tape and the power cable near the front of the unit. Blu-ray will be closed.

Cleaning the Blu-Ray

  1. Turn the player upside down, shows that the sub-board upward. The two screws on the edge of the board and the metal clips on the two later. Keep an eye on hand during removal and installation of the Blu-Ray.
  2. Remove the six screws on the top plate of the head portion of the Blu-Ray.
  3. Remove the connectors on the circuit by lifting and pulling on them. Lift the card which are linked from the strip. Gently pull the tape and remove the card. Bring the 'unit and lift the top cover to remove it.
  4. Remove the four screws under the top cover. Once the four screws are removed, further dissolution at the center of the rear edge of the converter. Lift the rear cover of the inside of the disk where the lens is exposed.
  5. Remove excessive dust blown by the player. Apply the cleaning solution in your lens cotton applicator and gently wipe the lens with a circular motion. Use the other end of cotton in a circular motion around the lens to be dried.
Please read other articles: Playstation 3 Console Deals

      0 comments:

      Post a Comment